Eldes ESIM264 Installationshandbuch Seite 54
- Seite / 140
- Inhaltsverzeichnis
- FEHLERBEHEBUNG
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
54
SMS
SMS text:
XXXX_INFO:00.00
Example: 1111_INFO:00.00
EKB2
Menu path:
OK → CONFIGURATION → PRIMARY SET → INFO SMS SCHED → PERIOD → [0]
OK → CONFIGURATION → PRIMARY SET → INFO SMS SCHED → TIME → [0]
EKB3
Enter parameter 11 & parameter status value:
[110000#]
SMS
N/A
EKB2
Menu path:
OK → CONFIGURATION → PRIMARY SET →
CALL/SMS SET → DIS CALL DUR ALM. → ENABLE
EKB3
Enter parameter 30 & parameter status value:
[301#]
This command disables Info SMS.
In case of alarm, the system makes a phone call to User 1. The phone call is made to the next
user in a row in case the previous user was unreachable (did not answer the call, was „out of
radio coverage“ or provi ded „busy“ signal). By default, this feature is enabled.
Disable Periodic
Info SMS
Disable Call in
Case of Alarm
NOTE: The system will not make a phone call to the next user in a row if the previous user was reachable, but rejected the phone call.
5.4.10 Alarm Notications
ATTENTION: Phone calls to the user in case of alarm become disabled when the system is connected to the monitoring station.
- INSTALLATION MANUAL 1
- Contents 3
- Installation Manual v2.2 6
- Limited Liability 7
- Manufacturer Warranty 7
- Package Content 7
- About Installation Manual 7
- 1. General Information 8
- 2. Technical Specications 11
- Fig. No.1 12
- 2.3 Wiring Diagrams 13
- Fig. No. 5 14
- Fig. No. 6 14
- Fig. No. 7 15
- Fig. No. 8 16
- Fig. No. 9 17
- 3. Installation 18
- 4. Operation Description 19
- 4.4 Wireless Devices 21
- 4.5 RS485 Interface 21
- 4.6 1-Wire® Interface 21
- 5. Conguration & Control 23
- CONFIGU 24
- XXXX_STCONFIG 25
- Shut down the 26
- Connection with 26
- Set SMS Language 26
- Set SMS Password 27
- Set User Password 27
- Delete User Password 28
- Replace User Password 28
- Set User Phone 30
- Delete User 30
- List User Phone 31
- Numbers 31
- Set Date & Time 32
- Arm the System 33
- Disarm the System 33
- Enable Arm 34
- Disarm by Zone 34
- Disable Arm 34
- Set Zone Alarm Text 35
- List Violated Zones 35
- Set Entry Delay 36
- List Violated 36
- Set Exit Delay 37
- Enable ATZ Mode 37
- Disable ATZ Mode 37
- - Type 1 38
- - Type 2 38
- - Type 3 38
- - Type 4 38
- - Type 5 38
- Disable Zone 39
- Enable Zone 39
- Bypass Zone 40
- Bypass All Zones 40
- Unbypass Zone 40
- Set Zone Type 41
- Enable Stay Mode 42
- Disable Stay Mode 43
- Activate Stay 43
- Mode Manually 43
- Disable Force Mode 44
- Enable Force Mode 44
- Disable Chime 45
- Enable Chime 46
- List Zone & PGM 46
- Output Status 46
- Set PGM Output Name 47
- Turn ON PGM Output 47
- / Set PGM Output 47
- Startup Status (ON) 47
- Example: 1111_C3:ON:13.23.48 48
- [49xx1#] 49
- [49xx0#] 49
- [3312#] 49
- Disable EPGM8 50
- Module Mode 50
- Set Siren Alarm 50
- Duration 50
- See Siren Alarm 51
- Enable Bell Squawk 51
- Disable Bell Squawk 51
- Info SMS 53
- Set Periodic 53
- Disable Periodic 54
- Disable Call in 54
- Case of Alarm 54
- Enable SMS in Case 61
- Loss/Restore 61
- Set Main Power 61
- Loss Delay 61
- Restore Delay 62
- Remote Listening 62
- Enable Control from 63
- Any Phone Number 63
- Disable Control from 63
- Set Keyboard Partition 64
- Switch Between 64
- Keyboard Partitions 64
- Enable Keyboard 64
- Partition Switch 64
- Set Zone Partition 66
- Set iButton® Partition 66
- Disable Event Log 67
- Enable Event Log 67
- Set Microphone Gain 68
- Set Speaker Level 68
- Reset to Default 69
- Parameters 69
- Menu path: 70
- 6.3 Troubleshooting 74
- 7. Wired Devices 76
- MAIN SCREEN VIEW 82
- DISABLE / ENABLE 85
- PARTITION [0... 1] 85
- 7.2 EKB3 - LED Keyboard 88
- FRONT SIDE 89
- AUX- AUX+ 90
- D1 D2 D3 D4 D5 D6 D7 D8 94
- 7.5 EA1 – Audio Output Module 96
- COM DATA 98
- Enable New iButton® 99
- Key Mode 99
- Disable New 99
- Check iButton® Key ID 100
- Delete iButton® Key ID 100
- Add Wireless Device 101
- Wireless Device Info 103
- Test Wireless Device 103
- EWT1 ESIM264 104
- Wireless Expansion 105
- Module EW1 105
- MAGNET SENSOR 109
- 8.5 EWK1 - Wireless Key-Fob 112
- RESETLED 114
- C1 C2 Z1 Z2 COM 122
- 9. Monitoring Station 124
- Enable Monitoring 125
- Station Mode 125
- Disable Monitoring 125
- Disable Data Message 126
- Enable User Message 127
- Disable User Message 128
- Set Account (Alarm 128
- System ID) 128
- Set Primary 129
- Connection 129
- Set Backup 129
- Connection (-s) 129
- Set Server IP Address 130
- Set Delay after Last 130
- Communication 130
- Set DNS1 Server 131
- IP Address 131
- Set DNS2 Server 131
- Set Server Port 131
- Set Protocol 132
- Set Local Port 132
- Set User 133
- Set Password 133
- Set Prole 133
- Set Unit ID 134
- Set Attempts 134
- Set Monitoring Station 135
- Phone Number 135
- Set Test Period 135
- Delete Monitoring 136
- Station Phone Number 136
- For notes 138
- Made in Lithuania 140
Verwandte Produkte und Handbücher für Sicherheitszugriffskontrollsysteme Eldes ESIM264
(28 Seiten)
(44 Seiten)© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.113 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern