Eldes ESIM264 Installationshandbuch PDF herunterladen (Seite 21)

Manual ElDES ESIM264 v2.2 21

4.3 Programmable Outputs (PGM)

The system ESIM264 has 4 built-in on-board PGM outputs allowing to connect and control various electrical appliances: water pumps,

heating, lighting, blinds etc. The number of PGM outputs can be expanded by:

• connecting EPGM8 - PGM output expansion module;

• connecting EPGM1 - zone & PGM output expansion module;

• adding the wireless devices.

The maximum supported PGM output number is 44.

ESIM264 PGM outputs are classied by 4 categories:

PGM Output Category Description

Max. Number of

PGM Outputs per

Device

Max. Number of

PGM Outputs in

Total

On-board PGM Outputs Built-in wired PGM outputs of ESIM264 alarm system. 4 4

EPGM8 PGM Outputs

Built-in wired PGM outputs of EPGM8 - PGM output expan-

sion module.

8 8

EPGM1 PGM Outputs

Built-in wired PGM outputs of EPGM1 - zone & PGM output

expansion module.

2 2

Wireless PGM Outputs

Non-physical PGM outputs automatically created by con-

nected wireless devices.

2* 32**

* - Depends on the connected wireless device.

** - Available only if no EPGM1 PGM outputs are present.

The C13-C44 PGM output numbers are assigned automatically in the chronological order of the devices connected to the system:

wireless devices, EPGM1 module. However, C1-C12 PGM output numbers are permanently reserved for on-board PGM outputs and

EPGM8 PGM outputs even if this module is not connected to the system.

For more details, please, refer to ELDES Conguration Tool software’s HELP section and chapter 5.4.7 PGM Outputs.

4.4 Wireless Devices

ESIM264 with installed EWT1 module operates as an access point for ELDES wireless devices: PIR movement sensor EWP1, expansion

modules EW1 & EW1B, sirens EWS1 & EWS2, magnetic door contact EWD1 and key-fob EWK1. Up to 16 ELDES wireless devices located

at up to 30 meters (up to 150 meters in open areas) radius range from ESIM264 alarm system with EWT1 can be connected at a time.

Accord ing to wireless device type and quantity the system adds wireless zones and wireless PGM outputs, therefore totally 32 wire-

less zones and/or 32 wireless PGM outputs can be added to the system. ELDES wireless connection operates at 868MHz non-licensed

frequency. For more details, please, refer to chapter 8. ELDES Wireless Devices.

4.5 RS485 Interface

ESIM264 has an RS485 interface supporting up to 4 EKB2 and/or EKB3 keyboards. This feature allows to install more than one alarm

system control point in the secured area in order to be able to arm and disarm the alarm system at several entrance points.

The RS485 interface is also intended for EPGM1 module connection and RS485 data channel connection to monitoring station.

For more details, please, refer to chapter 7. Wired Devices.

4.6 1-Wire® Interface

The implemented 1-Wire® interface enables the iButton® key reader connection to ESIM264. The system supports unlimited quantity

of iButton® key readers. For more details, please, refer to chapter 7.7 iButton® Key Reader & Keys.

1-Wire® interface is also intended for temperature sensor connection. Only 1 temperature sensor can be connected to ESIM264 sys-

tem. For more details, please, refer to chapter 5.4.12 Temperature Change Notications.

In order to assure a stable signal between the connected iButton® reader/temperature sensor and 1-Wire® interface, the cable length

must not exceed 30 meters.

1 2 ... 16 17 18 19 20 21 22 23 24 25 26 ... 139 140

Kommentare zu diesen Handbüchern

Keine Kommentare

Eldes ESIM264 Installationshandbuch Seite 21

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Sicherheitszugriffskontrollsysteme Eldes ESIM264